Connections
GeNetix Nodes
GeNetix Nodes all support industry standard protocols Art-Net and sACN supporting DMX Output or DMX Input, GeNetix nodes differ in the number of DMX ports. GeNetix GN2, GN5, GN10 GN10P and GN10R all feature an inbuilt display for node configuration and displaying device status. The GeNetix GN5, GN10, GN10P and GN10R feature additional connections supporting MIDI, Timecode and 10Scene.
All GeNetix Nodes can be powered via PoE, with the GN2, GN5, GN10, GN10P and GN10R supporting PoE Mode A and Mode B. The GW2I and GW2O nodes are powered only via PoE, supporting Mode A only (PoE over the data pair). In addition to PoE power, the GN2 can be USB powered via it’s USB-C port. In addition to being PoE powered the GN5, GN10, GN10P and GN10R can be powered via their mains Line Input.
GN2
The GN2 can operate as an Art-Net or sACN Node utilising it’s network connection or can also be used as a USB-DMX interface for MagicQ PC Systems. The GN2 will unlock MagicQ PC Systems when connected via either USB or Network into 'Core Mode'.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
The GN2 can be either PoE powered or powered via it’s USB-C port.
| The GN2 can run in network mode but still be powered from USB - provided that it is not connected to a PC running MagicQ - if MagicQ is detected it will be switched to USB mode. |
GN4IP
The GN4IP can operate as an Art-Net or sACN Node utilising it’s network connection. The GN2 will unlock MagicQ PC Systems when connected via Network into 'Core Mode'.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
The GN4IP can be either PoE powered or powered via it’s USB-C port.
| The GN4IP Scene Act button allows users to activate and deactive scene 1 stored on the GN4IP, this can be used by holding the Scene Act button until the green LED flashes. |
GN5
The GN5 operates as an Art-Net or sACN Node utilising it’s network connection or can also be used as a USB-DMX interface for MagicQ PC Systems. The GN5 will unlock MagicQ PC Systems when connected via either USB or Network into Full 'Unlocked Mode'.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
The GN5 can be either PoE powered or mains powered. When connecting to a MagicQ PC system via USB, the unit must be either Mains or PoE powered.
GN10
The GN10 operates as an Art-Net or sACN Node utilising it’s network connection or can also be used as a USB-DMX interface for MagicQ PC Systems. The GN10 will unlock MagicQ PC Systems when connected via either USB or Network into Full 'Unlocked Mode'.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
The GN10 can be either PoE powered or mains powered. When connecting to a MagicQ PC system via USB, the unit must be either Mains or PoE powered.
GN10R
The GN10R operates as an Art-Net or sACN Node utilising it’s network connection or can also be used as a USB-DMX interface for MagicQ PC Systems. The GN10R will unlock MagicQ PC Systems when connected via either USB or Network into Full 'Unlocked Mode'.
The GN10R differs from the GN10 in its ports, instead of traditional DMX output ports the GN10R instead utilises RJ45 output ports allowing for connections to be made using network cables instead of DMX cables.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
| The 10 Output ports on the GN10R cannot be used for networking. |
The GN10R can be either PoE powered or mains powered. When connecting to a MagicQ PC system via USB, the unit must be either Mains or PoE powered.
GN10P
The GN10P operates as an Art-Net or sACN Node utilising it’s network connection or can also be used as a USB-DMX interface for MagicQ PC Systems. The GN10P will unlock MagicQ PC Systems when connected via either USB or Network into Full 'Unlocked Mode'.
The GN10P differs from the GN10 in its ports, the GN10P instead utilises Phoenix ports for DMX output instead of traditional 3 or 5-pin DMX.
| When unlocking PC based systems via Network, there is a limit of 2 MagicQ sessions in the network. When a 3rd MagicQ instance is connected (this could be a console or another PC system), network unlock for all devices will be stopped. |
The GN10P can be either PoE powered or mains powered. When connecting to a MagicQ PC system via USB, the unit must be either Mains or PoE powered.
USB Connection
The GN2, GN5, GN10, GN10P, GN10R have an optional USB connection, allowing them to be used in either USB or Network mode.
When a GeNetix node is connected via USB to a PC (Windows, Mac or Linux) with MagicQ running then the GeNetix node runs in USB mode, functioning as a MagicQ interface connected directly to the MagicQ application.
In USB mode it is treated just like a MagicQ Wing or Interface with the configuration being controlled from within MagicQ rather than from the GeNetix node. In this mode the node configuration is unused, although it is retained for when the node is used again in Network mode.
When in USB mode, the DMX outputs are configured in MagicQ from the Setup Window, VIEW DMX I/O. For GN5, GN10, GN10P and GN10R the MIDI, Timecode and 10Scene port are configured in MagicQ from the Setup Window, VIEW SETTINGS. The configuration is stored in the MagicQ show file as normal.
The node indicates USB mode on its front panel when in USB mode.
The node continues in USB mode even if the USB link is lost or MagicQ is stopped. To restart the node in Network mode, disconnect the USB or shut down the MagicQ and then power the GeNetix node on and off.
| Note that firmware upgrade is only supported over ChamNet, not over USB. Firmware upgrade can be carried out from the free MagicQ PC/Mac software, and from MagicQ and QuickQ consoles. |
GW2I / GW2O
GW2I / GW2O Wiring
The GW2I and GW2O nodes are wired using either Cat5e or Cat6 cable using their punch down terminals. When wired via T568B wiring the GW2’s are wired as shown below:
| When using PoE injectors these must support PoE Mode A (PoE over the data pair), many budget PoE injectors provide data over the unused data pair only. Care should be taken when selection a PoE device to power the GW2I / GW2O nodes. The GeNetix GS8 Gigabit PoE switch support PoE Mode A and Mode B and is ideal for powering all GeNetix Nodes. |
GeNetix Switches
GS5IP
The GeNetix Switch 5IP or GS5IP is a five port IP65-rated unmanaged Gigabit network switch that can be powered via either mains power into its PowerCon True1 Mains Input connector or through PoE. The onboard Port Status LED’s provide users a visual indication to the current active state of the ports as well as showing if the switch is running at Gigabit speed.
The GS5IP will not unlock any MagicQ PC Systems.
| The GS5IP is a unmanaged network switch. Any network data received into the DATA IN port will be duplicated and outputted through all 4 ports. ChamSys Hardware and Software is not required to use this product. |
GS8
The GeNetix Switch 8 or GS8 is an eight port unmanaged Gigabit PoE network switch that provides a total output of up to 200W of Power over Ethernet across its eight ports. Ports 1 through 4 support IEEE 802.3bt up to 100W per port. In modes A & B, all ports 802.3af and 802.3at standards. The GS8 can be powered via the PowerCon True1 Mains input connector on the rear of the GS8.
The GS8 will not unlock any MagicQ PC Systems.
| The GS8 is a unmanaged network switch. Any network data received will be duplicated and outputted through all ports |
GeNetix DMX Splitters
GD4IP
The GD4IP is a compact 4-port IP65-rated DMX Splitter that features a single DMX Input to 4 DMX outputs, alongside this is a RDM Disable button allowing users to strip out RDM data and retime the DMX signal. The onboard Port Status LED’s provide users a visual indication to the active state of the ports.
The GD4IP is powered via its PowerCon True1 Mains input connector.
| Any DMX data the GD4IP receives through its "DMX IN" port is duplicated to all outputs. RDM data can be enabled or disabled using the "RDM disable" button. ChamSys hardware and software is not required to use this product. |
GD10
The GD10 is a 10-port DMX Splitter that features 2 DMX Inputs to 10 DMX outputs, alongside this is a RDM Disable button allowing users to strip out RDM data and retime the DMX signal. The onboard Port Status LED’s provide users a visual indication to the active state of the ports.
The GD10 offers two modes of operation:
1/10 mode where 1 source of DMX Input is split between all 10 DMX outputs.
2/5 mode where 2 sources of DMX Input is split equally between 10 DMX outputs with source 1 outputting through ports 1-5 and source 2 outputting through ports 6-10.
The GD10 is powered via its PowerCon True1 Mains input connector.
| RDM data can be enabled or disabled using the "RDM enable" button. ChamSys hardware and software is not required to use this product. |
GeNetix 10Scene Interfaces
10Scene Store
The GeNetix 10Scene Store is a single universe wall or DIN Rail mounted stand-alone playback device that stores 10 static lighting Scenes (cues) which can recall stored scenes through connected 10Scene wall plates. Users can load Scenes from either QuickQ or MagicQ show files or program via its in-built DMX Input port.
The 10Scene Store is powered by either PoE or external 48V power supply (not supplied). A suitable DIN Rail Mount power supply example is the Powerld DG-60-S48 which has been tested and proven with the GeNetix 10Scene Store. This simple installation device supports up to ten 10Scene wall plates, and features one DMX IN (XLR5 & Wago), one DMX OUT (Wago) and a network port.
| The 10Scene Store can be configured via a MagicQ system or through the GeNetix Web Server. |
10Scene Gateway
The 10Scene Gateway is an interface allowing users to connect 10Scene Wall Plates to MagicQ/QuickQ systems. Converting from 10Scene to the ChamSys remote protocol, allowing 10Scene Wall Plates to integrate with MagicQ and QuickQ consoles.
2 10Scene ports allow users to connect up to 20 10Scene Wall Plates, providing a perfect solution for adding user friendly control to installations.
The 10Scene Gateway is powered via either via PoE or an external power supply.
10Scene Wall Plates
The 10Scene Wall Plate features ten 10Scene trigger buttons, with dual colour LED status indication.
Users can connect 10Scene wall plates directly to the QuickQ Rack or to the SnakeSys Gateway interface, where it can then integrate with any MagicQ or QuickQ system for remote Scene activation.
