Timecode Support
MagicQ supports both time code decode and time code generation.
MagicQ MQ70, MQ80, MQ250M and MQ500 consoles have inbuilt support for Timecode. MagicQ consoles do not support timecode via 3rd USB party MIDI interfaces or through the console phono (rca) interfaces. For MQ80 and MQ500 we recommend using a balanced input. For MQ70 it can be balanced or unbalanced.
On MagicQ PC / Mac systems MIDI and timecode can be received using an external MagicQ MIDI/Timecode interface or a 3rd party USB/Virtual MIDI interface. Timecode and MIDI beat clock are only supported on 3rd party USB/Virtual MIDI when a MagicQ Wing or Interface is connected. MIDI notes is only supported on 3rd party USB interfaces when a ChamSys rack mount dongle is attached. For timecode we recommend the Adrem solutions TC1 time code reader (http://www.adrem-solutions.com).
MagicHD can also be used as a timecode input source for MagicQ systems supporting timecode.
Cue Stacks can be set up to run Cues according to timecode signals received from external sources via LTC or MIDI timecode. They can also be set up to use an Internal timecode source which is activated from 0:0:0 when the Cue Stack is activated and runs at 100 frames per second.
If a Cue Stack is intended to be run from External Timecode then we recommend setting it to External Timecode when programming so that the timecode frames match the expected input times rather than the 100 frames per second of the internal timecode. If there is timecode input available then the Timecode Simulator can be used to simulate receiving external timecode.
See Timecode Cue Stacks.
Automation events can be triggered by timecode.
Timecode Decode
MagicQ supports decode of both linear time code (LTC) and MIDI time code.
Set the Timecode Decode to LTC, MIDI, Art-Net or Internal MagicHD depending on the timecode source.
The timecode type can be set to EBU-25, SMPTE30, NTSC30 and Film 24. The Status Display will show the current timecode being received.
The timecode continue frames is the number of frames to continue internal regeneration of the timecode signal when it is lost. After this time the timecode will be frozen until a signal is received again.
Time code can be triggered from an external timecode source using the MagicQ MIDI/Timecode module, or it can run from the internal time code source. To control a Cue Stack using external timecode set the "External timecode" option in the Cue Stack options.
Timecode from Winamp
On a PC, timecode can be received from Winamp instead of from a MagicQ MIDI/SMPTE interface.
The PC must have a MagicQ Wing or MagicQ Interface connected, or be connected to a network with a MagicQ console. If connected via network then check in Setup, View Status, Net Consoles that the MagicQ PC can see the MagicQ console in the network. It should report status 03c3. If it can not see the console check that MagicQ (mqqt.exe) is not being blocked by a firewall such as Windows Defender.
Patch a Winamp personality in MagicQ (winamp_winamp.hed). If there is no Winamp personality in the show file then MagicQ will not connect to Winamp.
When MagicQ has a Winamp personality patched, MagicQ detects the instance of Winamp running and connects to it automatically. There is no need to configure anything in Winamp.
Set Timecode Decode to Winamp - the received timecode will be shown in the status display prefixed by "WTC".
When a file is played in Winamp the timecode will start running. Winamp typically starts the first track at 1/0/0 instead of 0/0/0 - but this will depend on how you set up the tracks in Winamp.
Timecode from MagicHD
MagicHD can send timecode for the currently playing video, either over Art-Net or directly into MagicQ (if running as the internal player).
Set the "Timecode Output" channel of MagicHD (#047) on the output layer to a value from 128 to 136, to select which video layer will be used for the timecode. On the MEDIA window, this can be found under Output > Control > Encoder D.
If using MagicHD and MagicQ on the same PC, set "timecode decode" in the settings (under View Settings > MIDI Timecode) to "Internal MagicHD"; MagicQ will now receive the timecode directly.
If using MagicHD stand alone networked to a MagicQ system (either console or PC), set "timecode generation" to "Art-Net "
On the standalone player, MagicHD will always output over Art-Net if "Timecode Output" is over 128 and MagicHD is out of demo mode (i.e. there is a ChamSys console or unlocked MagicQ instance on the local network).
Timecode Simulator
MagicQ includes a powerful timecode simulator for simulating external timecode when an external timecode source is not available. In the Setup Window, the simulator is turned on using soft button Y. When the simulator is on, then any received external timecode is ignored.
The timecode start value can be set by entering a timecode value and pressing the X soft button. The X soft button is also used to start and stop the timecode running.
Entering a new timecode value whilst the timecode simulator is running will jump directly to the new value and continue running.
Typing * before pressing the X button will restart from the last entered timecode.
Timecode Generation
MagicQ can also master timecode. Timecode Generation takes priority over Timecode Decode, so only enable Timecode Generation if it is required.
Set Timecode Generation to LTC, MIDI or Art-Net or combinations of the protocols.
When generating Timecode the Timecode Decode setting should be set to None.
Free running timecode
There are special Cue Stack macros to enable time code mastering and to set the time code value.
W <enable> Enable / disable time code generation (1 for enable, 0 for disable)
Q <time code> Set current time code (also enables time code generation)
For example to set timecode to 0/01/00.00
Enter Q100 at the cue stack macro.
MagicQ consoles generate MIDI and LTC timecode in hardware, and you must use a Y-split cable (with LTC) or MIDI splitter if you want MagicQ to see this timecode. |
Using Cue Stack internal timecode
To generate timecode based on the internal timecode of a Cue Stack. Use the Cue Stack macro W 2 in the Cue Stack you wish to use. MagicQ will use the timing of the Cue Stack from the Playback where the W 2 macro was last run.
To stop generation from the internal timecode of a Cue Stack and return to no timecode generation or free running timecode generation use the W 0 or W 1 Cue Stack macros.
Note that timecode will only be generated from a Cue Stack internal timing if the Cue Stack is active and it is set to internal timecode.
Timecode Re-transmit
The LTC or MIDI timecode decoded from a MagicQ MIDI/Timecode interface or from Winamp can be retransmitted over the network as Art-Net timecode.
This can then be received by any MagicQ console on the network even if it does not have a MIDI/SMPTE interface - just set the timecode input type to Art-Net.
For MagicQ PC/Mac systems the receiving system must have a MagicQ Wing or MagicQ Interface connected to enable the decoding of the Art-Net timecode - but this does not have to be a MagicQ MIDI/SMPTE interface.
PC/Mac systems with Winamp must have a MagicQ Wing or MagicQ Interface connected to enable the timecode to be received from Winamp.
Multiple timecode sources
FRom v1.9.6.0 MagicQ supports multiple external timecode sources, with the addition of 10 additional timecode sources received over ChamNet from GeNetix GN5 and GN10 devices.
The operation of the main external timecode source remains the same - it is configured in Setup, View Settings, MIDI/Timecode with choice of incoming timecode protocol, including LTC, MIDI, Art-Net and ChamNet set by the Timecode Decode setting as before.
By default, GN5 and GN10 devices are set to the default ChamNet ID of "Def" (0) with ChamNet timecode sent to MagicQ and QuickQ consoles as the Default timecode source. When they are set to a ChamNet ID of 1 to 10 they will send timecode on that ChamNet ID.
The status of the incoming ChamNet timecode can be viewed in the Timecode/DJ tab in Setup, View Status.
Cue Stacks now have a TC Source option in Cue Stack, View Options enabling them to listen to a different timecode source from the main external timecode. Cues Stacks default to the "Default" source. It can also be set to CH1 to CH10 to select timecode from a non default ChamNet ID.
The Timecode activate/release option in Setup, View Settings, MIDI/Timecode applies to Cue Stacks set to use the Default timecode and also to Cue Stacks set to use ChamNet ID 1 to 10. For each Cue Stack it will use the associated timecode source to determine activation and release.
In the Execute Window, Assign Special it is possible to assign items to show the main timecode and also for each of the timecode sources from ChamNet ID 1 to 10.
Note that on GeNetix and 10Scene Store the ChamNet ID also determines ID used for the close contact inputs on the 10Scene ports.